Files
CPY_PowerBus/TTU/Core/Src/main.c
T

443 lines
12 KiB
C

/* USER CODE BEGIN Header */
/**
******************************************************************************
* @file : main.c
* @brief : Main program body
******************************************************************************
* @attention
*
* Copyright (c) 2023 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
*/
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "adc.h"
#include "dma.h"
#include "iwdg.h"
#include "usart.h"
#include "gpio.h"
/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include "stdio.h"
#include "stdlib.h"
#include "math.h"
#include <string.h> // 用于memset函数
//#include "modbus_core_crc.h"
/* USER CODE END Includes */
/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */
uint8_t gucAddr = 0x40;
#define SLAVE_ADDR gucAddr // Modbus从机地址
#define TEMP_REG_ADDR 0x0000 // 温度 *10
uint8_t modbusRxBuf[16]; // Modbus接收缓冲匿
uint8_t modbusTxBuf[16]; // Modbus发鿁缓冲区
volatile uint8_t rxFlag = 0; // 接收完成标志
static uint16_t temp;
static uint16_t level;
//uint8_t UART1_Rx_flg = 0;
/* USER CODE END PTD */
/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD */
/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */
static float thermistor[4];
static uint16_t adc_value[4];
uint16_t temp_value[4];
float tem_compare[4];
/* USER CODE END PM */
/* Private variables ---------------------------------------------------------*/
/* USER CODE BEGIN PV */
/* USER CODE END PV */
/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_NVIC_Init(void);
/* USER CODE BEGIN PFP */
/* USER CODE END PFP */
/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */
static uint8_t uartRecvCnt = 0;
static uint32_t ulUartRecvTime = 0;
void get_level(void);
void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart)
{
if(huart->Instance == USART2){
HAL_UART_Receive_IT(huart, modbusRxBuf, 1); // 重新启动接收
}
}
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart) {
if(huart->Instance == USART2){
if(uartRecvCnt == 0 && modbusRxBuf[0] != SLAVE_ADDR){
HAL_UART_Receive_IT(huart, modbusRxBuf, 1); // 非本机地￿?,重置接￿?
return;
}
if(++uartRecvCnt >= 8){ // 接收￿?8字节,触发处￿?
uartRecvCnt = 0;
rxFlag = 1; // 设置接收完成标志
}
HAL_UART_Receive_IT(huart, &modbusRxBuf[uartRecvCnt], 1); // 继续接收下一个字￿?
ulUartRecvTime = 0;
}
}
uint16_t CRC16(uint8_t *buf, int len)
{
uint16_t crc = 0xFFFF;
for(int pos=0; pos<len; pos++){
crc ^= (uint16_t)buf[pos];
for(int i=8; i!=0; i--){
if((crc & 0x0001) != 0){
crc >>= 1;
crc ^= 0xA001; // Modbus CRC多项￿?
}else{
crc >>= 1;
}
}
}
return crc;
}
void AppendCRC(uint8_t* buf, uint8_t len)
{
uint16_t crc = CRC16(buf, len);
buf[len] = crc & 0xFF; // 低字节在剿
buf[len+1] = crc >> 8; // 高字节在吿
}
void Process_Modbus(void)
{
//printf("modbusr\r\n");
/* 第一层地坿过滤 */
if(modbusRxBuf[0] != SLAVE_ADDR) return; // 非本机地坿,直接忽畿
//printf("addr ok\r\n");
/* 第二层CRC验证 */
uint16_t crc = CRC16(modbusRxBuf, 6);
if(*(uint16_t*)&modbusRxBuf[6] != crc) return; // CRC校验失败,忽畿
//printf("crc ok\r\n");
switch(modbusRxBuf[1]){ // 根据功能码处琿
case 0x03: // 读保持寄存器
if(*(uint16_t*)&modbusRxBuf[3] == TEMP_REG_ADDR) // 棿查寄存器地坿
{
modbusTxBuf[0] = SLAVE_ADDR; // 从机地址
modbusTxBuf[1] = 0x03; // 功能砿
modbusTxBuf[2] = 0x02; // 返回字节敿(2字节)
uint16_t temp = temp_value[3]; // 模拟温度倿(实际应从传感器读叿)
modbusTxBuf[3] = temp >> 8; // 高字芿
modbusTxBuf[4] = temp & 0xFF; // 低字芿
AppendCRC(modbusTxBuf, 5); // 添加CRC校验
HAL_UART_Transmit(&huart2, modbusTxBuf, 7, 100); // 发鿿7字节响应
}
break;
// 可以添加其他功能码处琿
}
memset(modbusTxBuf, 0, sizeof(modbusTxBuf)); // 清空发鿁缓冲区
}
//re_def
int fputc(int ch, FILE *f)
{
HAL_UART_Transmit(&huart1, (uint8_t *)&ch, 1, 0xffff);
return ch;
}
//count temp
static float getTemp(float Rt)
{
const float Rp = 10000.0; ///< 10K NTC
const float T2 = (273.15+25.0); ///< 10K NTC
const float Bx = 3950.0; ///< 10K NTC
const float Ka = 273.15; ///< 10K NTC
float Temp = 0.0f;
Temp = Rt / Rp;
Temp = log(Temp);
Temp /=Bx;
Temp += (1 / T2);
Temp = 1 / Temp;
Temp -= Ka;
return Temp;
}
//adc adv
void float_to_int(void)
{
for(int i=0;i<4;i++)
{
temp_value[i]=(floor)(getTemp(thermistor[i])*10);
}
}
void adc_to_Rt(void)
{
float vol[4] = {0,0,0,0};
HAL_ADC_Start_DMA(&hadc1, (uint32_t *)&adc_value, 4);
for(int i=0 ; i<4 ;i++)
{
vol[i] = ((float)adc_value[i]/4095);
vol[i] = vol[i]*3.3 ;
thermistor[i] = (10000*vol[i])/(3.3-vol[i]);
}
}
int addr_test(void)
{
GPIO_InitTypeDef GPIO_InitStruct = {0};
GPIO_InitStruct.Pin = GPIO_PIN_7;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_9, GPIO_PIN_RESET);
HAL_Delay(10);
if (HAL_GPIO_ReadPin(GPIOB, GPIO_PIN_7) == GPIO_PIN_RESET) {
return 1;
}
return 0;
}
/* USER CODE END 0 */
/**
* @brief The application entry point.
* @retval int
*/
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration--------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* USER CODE BEGIN Init */
/* USER CODE END Init */
/* Configure the system clock */
SystemClock_Config();
/* USER CODE BEGIN SysInit */
/* USER CODE END SysInit */
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_DMA_Init();
MX_ADC1_Init();
MX_USART2_UART_Init();
MX_USART1_UART_Init();
MX_IWDG_Init();
/* Initialize interrupts */
MX_NVIC_Init();
/* USER CODE BEGIN 2 */
//Set GPIO NMOS COLSE
HAL_GPIO_WritePin(GPIOA,GPIO_PIN_HEATER,GPIO_PIN_RESET);
HAL_UART_Receive_IT(&huart2, modbusRxBuf, 1); // 重新启动接收
int a = 0;
for (int i = 0; i < 10; i++) {
HAL_IWDG_Refresh(&hiwdg);
HAL_Delay(10);
}
HAL_IWDG_Refresh(&hiwdg);
if (addr_test()) {
gucAddr++;
}
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
HAL_IWDG_Refresh(&hiwdg);
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
ulUartRecvTime++;
if ((uartRecvCnt > 0) && (ulUartRecvTime > 3)) {
HAL_UART_AbortReceive_IT(&huart2);
uartRecvCnt = 0;
HAL_UART_Receive_IT(&huart2, modbusRxBuf, 1); // 重新启动接收
}
if(rxFlag){ // 棿查是否接收到完整Modbus数据帿
rxFlag = 0; // 清除标志
Process_Modbus(); // 处理Modbus命令
}
if (a % 900 == 0) //每秒读一次温度
{
adc_to_Rt();
float_to_int();
printf("Temp_value:");
printf("%d,",a/100);
for(int i=0;i<4;i++)
{
printf("%d,",temp_value[i]);
}
printf("%d,",level);
printf("\r\n");
}
if(a++ > 50000)
{
a = 0;
}
HAL_Delay(1);
}
/* USER CODE END 3 */
}
/**
* @brief System Clock Configuration
* @retval None
*/
void SystemClock_Config(void)
{
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
/** Configure the main internal regulator output voltage
*/
HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
/** Initializes the RCC Oscillators according to the specified parameters
* in the RCC_OscInitTypeDef structure.
*/
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_LSI;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSIDiv = RCC_HSI_DIV1;
RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
RCC_OscInitStruct.LSIState = RCC_LSI_ON;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
RCC_OscInitStruct.PLL.PLLM = RCC_PLLM_DIV1;
RCC_OscInitStruct.PLL.PLLN = 8;
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV11;
RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV2;
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
{
Error_Handler();
}
/** Initializes the CPU, AHB and APB buses clocks
*/
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
|RCC_CLOCKTYPE_PCLK1;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
{
Error_Handler();
}
}
/**
* @brief NVIC Configuration.
* @retval None
*/
static void MX_NVIC_Init(void)
{
/* USART2_IRQn interrupt configuration */
HAL_NVIC_SetPriority(USART2_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART2_IRQn);
}
/* USER CODE BEGIN 4 */
/* USER CODE END 4 */
/**
* @brief This function is executed in case of error occurrence.
* @retval None
*/
void Error_Handler(void)
{
/* USER CODE BEGIN Error_Handler_Debug */
/* User can add his own implementation to report the HAL error return state */
__disable_irq();
while (1)
{
}
/* USER CODE END Error_Handler_Debug */
}
#ifdef USE_FULL_ASSERT
/**
* @brief Reports the name of the source file and the source line number
* where the assert_param error has occurred.
* @param file: pointer to the source file name
* @param line: assert_param error line source number
* @retval None
*/
void assert_failed(uint8_t *file, uint32_t line)
{
/* USER CODE BEGIN 6 */
/* User can add his own implementation to report the file name and line number,
ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
/* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */